We build and install hydrogen generators for your car, truck or boat.
Our clients have hired us to fabricate for special fleet usage also for custom built
vessels.

Our backround is over 25 years in the automotive industry, we have the tools
knowledge to take your vehicles to the next level of enhanced fuel use.

   But if you want to build them yourself we will supply you with the parts
Consulting
Analysis
Advice
Contact us at Sales@waterpowercorp.com     help save the planet
| water gas|browns water|hydrogen|watergas|Run your car on water|Gas|
                     Water Power Corp .com All right reserved 2008
                        Contact: sales@waterpowercorp.com
kynar housing,viton
diaphragm disc check
valves used in line of
your output tube on your
system 3/8 size ID cost
us $1.44pc
sku 64049  Everything
you Need to install unit

No  Handling Charges
3/4" nylon plugs for
cap end of your
generator
sku# 64696
our cost $0.80


No  Handling Charges .

nylon barbed end  
nylon connector
for 3/4 " to 3/8" ID
tubing
sku 61147
our cost $1.30

No  Handling Charges
General purpose
High temp high pressure
tubing 3/8 ID sold in 10 ft
lengths
sku 60126 Blue  cost us
$ 12.00 for 10 ft  

No  Handling Charges
Nylon reducer
bushings 3/4" to 1/2"
nylon reducer NSF
listed
SKU #62244
our cost $1.50

No  Handling Charges
MADE IN THE USA
DIESEL FUEL
             SYSTEMS
Building,installing, hydrogen generators in cars and trucks for years to come.
Waterpowercorp.com
Waterpowercorp.com
Our HHO Parts , can save you Time.

"NEW"
Fuel
Economy
   GUIDE
Our standard built Map enhancer
comes complete with 12' wiring
harness and marked  lead and
instruction for easy installation.
sku #2225  $60.00
   No  Handling Charges
One of the  best on the market  built
Map enhancer. Design to tell you when
you are low on water in your generator
from inside the car. Tells you when
your systems is on, also indicates if
your cell is running to hot before there
is a problem.   Comes complete with
12' wiring harness and marked  lead
and instruction for easy installation.
No  Handling Charges  Sku 2226
$120.00
Reducing plates on Hydrogen generators video
Nylon barb end  check
valves for vacuum  used
in line of your output
tube on your system 3/8  
to 1/4 size ID SKU
64004
our cost $10.00

No  Handling Charges
Nylon barb end  90
degree fittings used in
line of your output tube
on your system 3/8 size
ID 3/8 npt
sku #63103
our cost  $1.20

No  Handling Charges.
Bubbler valve
140F temp 3/8 FNPT
and 3/8 MNPT  with
Buna seal
sku 22133
our cost $16.00 pc

No  Handling Charges
Disclaimer: Hydrogen gas can be very dangerous if handled improperly. These
cells are to be used by qualified individuals for personal use in the generation of
Hydrogen for experimental purposes only.
                         * All parts shipped United States Postal Service*
We suggest email us if you are looking to buy more than on item, because you
can get savings on shipping and quantity discounts.
                        * All parts shipped United States Postal Service*
We suggest email us if you are looking to buy more than on item, because
you can get savings on shipping and quantity discounts.

Are you looking for something not shown here?  Email us chances are we
have what you are looking for.
The Best designed
Pulse Width Modulation
Control, Uses: Motor
Control, DC Dimmer,
Electrolysis, Heating
control. 30 Amps @ 12 or
24 volts DC. Fully
Assembled & Tested
New  Flame dissapator from
HHOG Labs. A must for
anybody who is building a
hydrogen system, every
system should have one.
The best solution to use
on your system
give you optimum
proformance and keeps
your cells clean. Just a
few onces at a time